Rodney Dickman's Automotive Accessories Checkout   
  Top » Catalog » •Cooling System » My Account  |  Cart Contents  |  Checkout   
Categories
•Delorean Parts, etc
•Pontiac Mera
•Replacement Sander Pads
•Corvette Headlight Gears
•Corvette & GM Tach Filters
•Firebird Headlight Gears
•GM Headlight Rebuild (Other)
•Ford Window Rebuilding
•Getrag 238 bearing retainer
•Chrysler Light Motor Repair
•Chrysler Electric Window Repair
•Buick Reatta
•Audi
•Lotus
•Ferrari
•Kubota Lawn Mowers
•Dyson Hand Held Vacs
•Star (Torx) Exhaust Studs
•Isuzu Trooper 3.4 Swap
•Kit Car Parts & Acc's
•Zero Lash Sway Bar Links
•Fiero Apparel
•Fiero Stickers
•Fiero Audio
•Brakes
•Electrical
•Fiero Headlight Gears
•Light Bulbs
•Cooling System
•Fiero Engine
•Fiero Cables
•Fiero Exhaust
•Fiero 3.4 Engine Swap
•Fiero Interior
•Fiero Exterior
•Fiero Shifters
•Shifter Boots, Rebuild Kits etc
•Steering & Suspension->
•Fiero Tools
•Fiero Manuals
•Clutch Masters & Slave Cylinder
•Fiero Transaxles
•Research & Development
•Seconds, Sale Items, etc..
•Used Fiero parts
•Miscellaneous
What's New? more
Long Under Car Coolant Tube Installation Tips
Long Under Car Coolant Tube Installation Tips
$0.00
Information
Shipping & Returns
Privacy Notice
Conditions of Use
Contact Us
Long Under Car Coolant Tube Installation Tips $0.00

 

 

 

Helpful tips to install my long undercar coolant tube repair kits

 

I have made up some installation tips. As people buy and install these pipes some might offer me some extra tips and I'll add them as I get them.

 

 

Start by removing your front tire and the rearward or both front inner wheel well(s).

 

Cut your existing coolant tube halfway between the first and second bend. You can also hold my replacement tube in place to mark where the cut should be.

Hint;  The cut does not have to be perfect as you are installing a rubber hose over it. If your cut is at a slight angle you should not have to worry too much about it. You might also start slightly longer and grind it back some until you get a good match to my repair tube.

You will see the small inner stainless steel pipe piece I supply is two different diameters. GM had this coolant tube specially made. This GM size tube is a non standard size tube. So my long repair pieces have a smaller ID than the factory tubes. The large end goes in the OEM GM end and the smaller end goes in my repair section of pipe.

 

Fitting the small inner stainless steel piece into your front section OEM GM tube:

The OEM GM tube is welded and there is a burr line inside. The pipe is also generally at a slight oval because of the bending process. The inside weld burr line is wherever it happened to be as they made the tubes. So my small tube may not want to go into the OEM GM tube very well. I made them slightly smaller so they fit in the OEM GM tubes better.

A few tricks you can use: Put a C clamp on the tube to try and make it closer to being round. This may allow you to push or hammer in my small tube.

You can also grind a small flat area on the thicker end to help it go in the tube easiler (marked in black in the picture below).

If you have a high speed die grinder and grinding stone you can go in and grind this burr line down some if need be. Clean the inside of the tube before you go forward again.

 

 

 At this point I would install the long tube back in the car and install the front and rear body clamps and make sure everything fits well. Make any adjustments as needed. Once you are happy everything fits well drill and install some rivets into the OEM GM pipe end. There is probably not enough clearance to get 4 rivets at 90 degrees apart. Just do the best you can.

Do not drill and rivet the the new pipe end yet!

 

 

Remove the long tube. Slide the rubber hose piece and both clamps onto the OEM end of the coolant tube. Slide it back enough to work on the new pipe section. Install the new pipe and the clamps. Once everything is in place drill and install rivets into the new pipe.

 

Slide the rubber hose back and tighten the clamps.

 

 

 

Reinstall the inner fender liner and tire and you are finished.

 

 

 

 

 

This product was updated on Tuesday 10 December, 2019.
Reviews
Customers who bought this product also purchased
84-87 Under Car Replacement Coolant tubes
84-87 Under Car Replacement Coolant tubes
Shopping Cart more
0 items
Notifications more
NotificationsNotify me of updates to Long Under Car Coolant Tube Installation Tips
Tell A Friend
 
Tell someone you know about this product.
Parts Finder
 
Use keywords to find the product you are looking for.
Advanced Search
Reviews more
Write ReviewWrite a review on this product!

Copyright © 2020 Rodney Dickman's Automotive Accessories
Designed and Maintained by SoftNuTek