Rodney Dickman's Automotive Accessories Checkout   
  Top » Catalog » •Steering & Suspension » 1988 Fiero » My Account  |  Cart Contents  |  Checkout   
•Delorean Parts, etc
•Pontiac Mera
•Replacement Sander Pads
•Corvette Headlight Gears
•Corvette & GM Tach Filters
•Firebird Headlight Gears
•GM Headlight Rebuild (Other)
•Ford Window Rebuilding
•Getrag 238 bearing retainer
•Chrysler Light Motor Repair
•Chrysler Electric Window Repair
•Buick Reatta
•Kubota Lawn Mowers
•Dyson Hand Held Vacs
•Star (Torx) Exhaust Studs
•Isuzu Trooper 3.4 Swap
•Kit Car Parts & Acc's
•Zero Lash Sway Bar Links
•Fiero Apparel
•Fiero Stickers
•Fiero Audio
•Fiero Headlight Gears
•Light Bulbs
•Cooling System
•Fiero Engine
•Fiero Cables
•Fiero Exhaust
•Fiero 3.4 Engine Swap
•Fiero Interior
•Fiero Exterior
•Fiero Shifters
•Shifter Boots, Rebuild Kits etc
•Steering & Suspension->
  1984-87 Fiero
  1988 Fiero
•Fiero Tools
•Fiero Manuals
•Clutch Masters & Slave Cylinder
•Fiero Transaxles
•Research & Development
•Seconds, Sale Items, etc..
•Used Fiero parts
What's New? more
Audi Exhaust Pipe Coupling Repair Kit
Audi Exhaust Pipe Coupling Repair Kit
Shipping & Returns
Privacy Notice
Conditions of Use
Contact Us
Rebuildable 1988 Fiero Front Wheel Bearing Hubs $129.95




Rebuidable 1988 Fiero front wheel bearing hubs





I originally had a local engineer that had some experience with designing wheel bearing hubs make some preliminary CAD drawings. As this project moved along I contacted Paul Smith and he made some changes to fine tune the design and add some nice features like the thicker flange.

I had the forgings made in China and they are machined, heat and assemblied in Taiwan. They come with top quality Japan NSK bearings/races and a double lip rubber seal.


 This is a first prototype. We reduced the length of the threaded shaft and also lowered the height of the hub some to make the overall height less for the production run.You can see this in the pictures farther down.


Interior pictures:

Double lip seal Slots milled inside to allow removal of the inner races

 The steel cap is now on the inside of the hub.


These use common tappered wheel bearings. Both inner (bearing and race) and outer races are replacable and a double lip seal that most auto parts stores will have in stock or can get within a day or so.

Seal: Timken 494122 or equivalent

Large inner bearing (behind the seal): Timken 32007 or equivalent

Smaller outer bearing (under the gold cap)  Timken 32006 or equivalent


I will also stock replacement Nachi (Japan) high quality bearings and seals and all the misc parts used in these hubs. See this web page for replacement parts.


Not for racing




I have had a few requests to offer these in different bolt hole patterns.  I will have some spindles that are not drilled for the studs. The three holes for the attaching bolts will be drilled. You will need to take them to a machine shop and have them drill and ream them to the lug bolt pattern of your choice and the hole size needed for the lug bolts of your choice. I'm having them leave 50 not drilled for lug bolts.

50 have been left blank:




OEM GM part number for cross reference: 

GM OEM part number:  7466939

Interchange numbers:

513040      BR930039       7466939       20-39





I found another area of concern. The steel cap was very hard to pry off. So we changed the end of the housing to have a taper. This allows room to get a screwdriver under the cap to remove the cap:




How to set the castle nut:

This is my way of setting a slotted castle nut on an typical automotive front wheel bearing. There has to be a slight amount of play in them or the grease will get all pushed to the sides and the tapered rollers will overheat and start to fail.

(1) Tighten the castle nut finger tight.

(2) Use a channel locks and tighten the castle nut slightly more. 1/8 to 1/4 turn.

(3) Rotate the hub several times (10 is suggested).

(4) Loosen the castle nut using the channel locks.

(5) Tighten the castle nut finger tight.

(6) Observe the slots in the castle nut compared to the holes in the spindle. You need to back off the castle nut a minimum of one slot. So if a slot lines up perfectly with a hole - back off the castle nut one slot and install the pin. If the castle nut does not line up back it off until it does line up with a hole in the spindle then back the castle nut off one more slot. So your looseness range is one slot to 1.99 slots. An exception to this: If when finger tight the hole in the spindle is around half visible or more you can back it off just one slot.

(7) Install the cotter pin. Push the pin all the way into the slot. The large end of the pin fits perfectly into a slot so it has no chance of rotating.


How to grease a tapered wheel bearing:


This is the grease they used:



Torque the three (3) mounting bolts to 62 foot pounds. The 1988 GM service manual has the wrong value.




1988 rebuildable wheel hub:  $129.99 each

1988 rebuildable wheel hub W/O lug bolt holes:  $139.99 each






I do not offer free shipping.

Because I use postal flat rate boxes for heavy orders there is no program that can add the proper amount of shipping to every order. So all shipping is added manually by myself after you place your order. That is explained here: Shipping added later explanation 

When you place an order the shipping amount will show $0.00. Soon after you place an order you will receive an email confirmation that shows the amount of shipping that was added to your order.



Shipping:  In the USA, if you order a pair, I ship these in a medium flat rate box with a thin piece of plywood in the bottom of the box. Shipping is $18 for a pair shipped in the USA.



Price is per hub. If you want two (2) hubs you need to change the quantity to two (2).


Available Options:
This product was updated on Wednesday 23 October, 2019.
Customers who bought this product also purchased
Manual Mirror Repair Plate
Manual Mirror Repair Plate
V-6 OEM Look Dog Bones
V-6 OEM Look Dog Bones
Fiero Low Temp Radiator Fan Switches
Fiero Low Temp Radiator Fan Switches
High Temp Distributor O-ring
High Temp Distributor O-ring
1988 Rubber Radiator Hoses
1988 Rubber Radiator Hoses
1988 Steering Rack Poly Mounts
1988 Steering Rack Poly Mounts
Shopping Cart more
0 items
Notifications more
NotificationsNotify me of updates to Rebuildable 1988 Fiero Front Wheel Bearing Hubs
Tell A Friend
Tell someone you know about this product.
Parts Finder
Use keywords to find the product you are looking for.
Advanced Search
Reviews more
Write ReviewWrite a review on this product!

Copyright © 2020 Rodney Dickman's Automotive Accessories
Designed and Maintained by SoftNuTek