Rodney Dickman's Automotive Accessories Checkout   
  Top » Catalog » •Fiero Exterior » My Account  |  Cart Contents  |  Checkout   
•Delorean Parts, etc
•Pontiac Mera
•Replacement Sander Pads
•Corvette Headlight Gears
•Corvette & GM Tach Filters
•Firebird Headlight Gears
•GM Headlight Rebuild (Other)
•Ford Window Rebuilding
•Getrag 238 bearing retainer
•Chrysler Light Motor Repair
•Chrysler Electric Window Repair
•Buick Reatta
•Kubota Lawn Mowers
•Dyson Hand Held Vacs
•Star (Torx) Exhaust Studs
•Isuzu Trooper 3.4 Swap
•Kit Car Parts & Acc's
•Zero Lash Sway Bar Links
•Fiero Apparel
•Fiero Stickers
•Fiero Audio
•Fiero Headlight Gears
•Light Bulbs
•Cooling System
•Fiero Engine
•Fiero Cables
•Fiero Exhaust
•Fiero 3.4 Engine Swap
•Fiero Interior
•Fiero Exterior
•Fiero Shifters
•Shifter Boots, Rebuild Kits etc
•Steering & Suspension->
•Fiero Tools
•Fiero Manuals
•Clutch Masters & Slave Cylinder
•Fiero Transaxles
•Research & Development
•Seconds, Sale Items, etc..
•Used Fiero parts
What's New? more
C5 Headlight Bucket Pivot Bolts
C5 Headlight Bucket Pivot Bolts
Shipping & Returns
Privacy Notice
Conditions of Use
Contact Us
"NEW" Hinge Mounted Rear Decklid Strut Kit $85.95



Hinge Mounted Rear Deck lid Strut Kit


I had someone (Fiero Jon) who needed a rear deck lid strut kit but he had an engine brace that was in the way of installing my typical rear deck lid strut kit. He still had the factory springs but added a wing and his rear deck lid would not stay up.

So I pondered this and came up with a new design that mounts to the drivers side rear deck lid hinge.


To start this kit is only for those that still have the factory springs still in place. This for those that have a rear deck lid that will not stay up.

My opinion is that to use a higher pressure strut for those that have removed the factory springs might make the rear deck lid warp over time. It would be a lot of pressure pushing upward when the rear deck lid is closed. My other rear deck lid strut kits have the struts close to parallel to the deck lid when the deck lid is closed. I may look in the future at making a dual kit for those that have removed both factory springs.




Easy to install. You remove one bolt from the upper arm and bolt in the upper bracket.


You remove one nut from the lower arm and bolt in the lower bracket.



There are three threaded holes in the lower bracket which allow for variations in the length needed. Once the brackets are installed you choose the hole in the bottom bracket that fit the extended length of the strut the best.




It’s a great product. I like it much better than the traditional struts 

Jeff Donnelly


There are 2 different types of rear deck lid hinges. Look at what type you have before ordering.


 This is the thick lower type with the small opening below the center pin:


 This is the thin lower type with the large opening below the center pin:


The kits differ because of the width of the lower arms on the hinges.



Clearance note: On Fiero Jon's he said his hit the factory spring slightly scratching the paint in one small area on the gas strut. But he said he would gladly put up with that to have a gas spring because of his engine brace and his lid not staying up. His was close to the vent and had no room to move outward any farther.This will vary on every car. Many should fit with no issues.





My suggestion:

Oil your hinge pins. They tend to rust and if the hinge pins rust too much they will seize and break. They are hardened steel and impossible to repair once they have seized and sheared off.







I do not offer free shipping.

Because I use postal flat rate boxes for heavy orders there is no program that can add the proper amount of shipping to every order. So all shipping is added manually by myself after you place your order. That is explained here: Shipping added later explanation 

When you place an order the shipping amount will show $0.00. Soon after you place an order you will receive an email confirmation that shows the amount of shipping that was added to your order.


Shipping:    Shipping in the midwest USA $10.00

Shipping to areas outside of the USA: Generally I ship postal air first class mail. Shipping varies depending on what country they are going to. It ranges from $18.25 to Canada to $27 or more to Australia etc.




Available Options:
This product was updated on Tuesday 12 February, 2019.
Customers who bought this product also purchased
Rear Deck Lid Hinge Straps
Rear Deck Lid Hinge Straps
Door Hinge and Em. Brake Spring Compressor
Door Hinge and Em. Brake Spring Compressor
1987-1992 Firebird Headlight Rebuild Kits
1987-1992 Firebird Headlight Rebuild Kits
Stant 180° Thermostat
Stant 180° Thermostat
85-88 Fastback Exhaust Tip Shield Plates
85-88 Fastback Exhaust Tip Shield Plates
Door Hinge Pin
Door Hinge Pin
Shopping Cart more
0 items
Notifications more
NotificationsNotify me of updates to "NEW" Hinge Mounted Rear Decklid Strut Kit
Tell A Friend
Tell someone you know about this product.
Parts Finder
Use keywords to find the product you are looking for.
Advanced Search
Reviews more
Write ReviewWrite a review on this product!

Copyright © 2020 Rodney Dickman's Automotive Accessories
Designed and Maintained by SoftNuTek